Recent Activity

Activity stream for all registered members at XWeb Forums v3 .

  1. Dr.Jeff attached a file to the thread Steering rack bushing failure mode?.

    I haven't done it on a Fiat rack, so can't say for sure. But it sounds like the one you tried before might have been rusted or corroded...

    s-l300.jpg Dec 19, 2018 at 4:01 AM
  2. TonyK replied to the thread Tubing bead Roller.

    Slab wood from the local saw mill. At the bottom of the picture was a coal scuttle (empty). I have about 1200 pounds of hard...

    Dec 19, 2018 at 3:18 AM
  3. TonyK replied to the thread Tubing bead Roller.

    Smallest would be 5/8" I.D. So yes there is lots of room as the small roller goes in the tube. TonyK.

    Dec 19, 2018 at 3:16 AM
  4. myredracer replied to the thread Need to reverse rotation of a Abarth A112 engine to counterclockwise.

    Have you priced out what getting them from BM would cost anyway? S/T in Germany is likely a fair bit cheaper.

    Dec 19, 2018 at 3:05 AM
  5. kmead replied to the thread Here is another k20 swap..

    Yes attaching the tank to the head will be good. I suspect you will have a failure in the welded connection of the pipe to the OE...

    Dec 19, 2018 at 2:59 AM
  6. kmead replied to the thread Here is another k20 swap..

    Well, that shudder is in your future I do believe :)

    Dec 19, 2018 at 2:53 AM
  7. Mark replied to the thread Stock Carpet Wanted.

    Traditionally, it was held down with strategically located trim screws, but a high quality spray adhesive works well.

    Dec 19, 2018 at 2:17 AM
  8. lookforjoe replied to the thread Tubing bead Roller.

    Nice. What is the smallest ID tube you can bead? Would it work for the 1 3/8" heater piping I made ? :D

    Dec 19, 2018 at 1:48 AM
  9. lookforjoe replied to the thread Turbo systems for X1/9's.

    I would say they are all similar, except that ones in the head itself would heat soak more so than the T/stat location when the engine...

    Dec 19, 2018 at 1:43 AM
  10. cozzoi replied to the thread Need to reverse rotation of a Abarth A112 engine to counterclockwise.

    Anthony Berni told me I need to order a LH rotation camshaft and a oil pump drive shaft below distributor. He was clear with the gear...

    Dec 19, 2018 at 12:57 AM
  11. Frank L. Di Gioia attached a file to the thread Need to reverse rotation of a Abarth A112 engine to counterclockwise.

    As mentioned earlier the A112 stainless steel 70hp header can easily be used on an 850. I forgot to take a pic before starting but the...

    DSCI0968.JPG DSCI0967.JPG Dec 19, 2018 at 12:54 AM
  12. lookforjoe replied to the thread Preparing For Honda K24a3/AST5 6spd Conversion.

    Finished up the main work on the header, runners all welded, merge collector welded. [IMG] [IMG] This is the comparison of the...

    Dec 19, 2018 at 12:26 AM
  13. 128kid replied to the thread X1/9 wanted.

    Give it time. It's holidays; said he just had a kid, etc.

    Dec 18, 2018 at 11:55 PM
  14. ibertone86 replied to the thread Stock Carpet Wanted.

    Is a segmented carpet installed with adhesive?

    Dec 18, 2018 at 11:46 PM
  15. Jeff Stich replied to the thread Need to reverse rotation of a Abarth A112 engine to counterclockwise.

    It is indeed possible, it's a known conversion method. Perhaps Tony just meant to say he's "out of stock" on this gearset (as in "It's...

    Dec 18, 2018 at 11:13 PM
Loading...
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice