<TABLE cellSpacing=1 cellPadding=6 width="100%" border=0><TBODY><TR><TD colSpan=2><TABLE width="100%" border=0><TBODY><TR><TD style="PADDING-TOP: 4px" vAlign=top colSpan=2>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Clutch Plate Centralisation<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001 at 4:36 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony Carroll [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->This post may be of assistance to you brave souls contemplating replacing your clutch unit and throwout bearing (the latter highly recommended).
This assumes that you are withdrawing your transmission unit only and leaving the engine in situ. With the whole oily mess on the floor, it may be wise to inspect the flywheel face and have it skimmed if necessary. A very light smear of grease on the G/B input splines is an idea after cleaning up with a rotary wire brush to reduce the chances of the clutch plate freezing on the splines as I suspect happened to Michael Hartel. Young players may notice that the short G/B input shaft is fully floating and is not supported by a spigot bearing in the crankshaft. Further bad news is that the hole in the end of the crank is larger than the I/D of the clutch plate hub, ruling out the use of a mandrel to centre the plate on reassembly. The manual says to line up the clutch plate by eye. Well, really!
My answer was to turn up a dummy spigot from mild steel and drilled smaller than the clutch hub I/D and long enough to reach the crankshaft flange. This is then pressed into the crank. Turn up a suitable mandrel to fit both dummy spigot and clutch plate hub and hang the clutch plate on this while you tighten the pressure plate. The whole plot should then go back together as easily as it came out. By the way, this all refers to a Euro-spec '82 X but the US specs in this area appear to be the same in the manual.
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Author[/FONT]</TD><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Reply[/FONT]</TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Warren[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->An easyer way<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001, 9:15 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I use a large felt marker to cenetre the clutch.
I have ued this method meany times.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony Carroll[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Good lateral thinking<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001, 10:41 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Nice one Warren. If I didn't have a lathe I may have thought of the same method but being brought up on North-South engines and "proper" gearboxes...<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]lezesig[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Several forms of alignment tool.<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 1:20 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Warren,
How about this variation ? A Store bought Splined alignment tool. Yep, actually broke down and bought one for the first time. Sure worked sweet. Like buying a one time use tool. Often overlooked when firing the order for the bearing, plate, and disk....but a very small expenditure comparitively speaking. This one was made of a durable plastic also.
.
You have to admit....spinning one on a lathe does have more class !! The question to Tony is - did he choose a fine or course knurl on the handle end ?
.
Out for now,
lezesig '79 X 1/9<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Mark Seelbinder[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Confused?$<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 7:12 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Why not order the correct alignment tool when you order the clutch parts? It is about $3!<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "m";n54_em = n54_em + "a";n54_em = n54_em + "c";n54_em = n54_em + "@";n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "a";n54_em = n54_em + "t";n54_em = n54_em + "t";n54_em = n54_em + "l";n54_em = n54_em + "e";n54_em = n54_em + "x";n54_em = n54_em + "1";n54_em = n54_em + "9";n54_em = n54_em + ".";n54_em = n54_em + "o";n54_em = n54_em + "r";n54_em = n54_em + "g"; document.write("Mac"); // --> </SCRIPT>Mac <NOSCRIPT></NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->alignment tool<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 4:05 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->That's the one we use, just an el cheapo plastic phony input shaft on a plastic ring. It says 'Fiat 128' on it. Use it to line up the disc while you bolt the pressure plate in place, and then hooah - up goes the tranny and the wiggling begins -Mac.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Warren[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You forgot to tell them that the tranny goes on after the swearing . <NT>
<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 8:39 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "m";n54_em = n54_em + "a";n54_em = n54_em + "c";n54_em = n54_em + "@";n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "a";n54_em = n54_em + "t";n54_em = n54_em + "t";n54_em = n54_em + "l";n54_em = n54_em + "e";n54_em = n54_em + "x";n54_em = n54_em + "1";n54_em = n54_em + "9";n54_em = n54_em + ".";n54_em = n54_em + "o";n54_em = n54_em + "r";n54_em = n54_em + "g"; document.write("Mac"); // --> </SCRIPT>Mac <NOSCRIPT></NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 60px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->D'oh! I always forget the most critical step<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 6:22 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 60px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->And speaking of forgotten steps, please don't forget to take the alignment tool back OUT after tightening the pp bolts and before hefting that tranny up over your head or you will end up swearing
-Mac.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony Carroll[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 75px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I did consider mentioning that step...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:26 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 75px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->but I would be the last person to insult the intelligence of those who read and learn from this board. In passing and referring to my original post, where I come from, most Fiats were privately imported (especially X1/9's) and my local Continental car dealer (Ferraris, Alfas, Fiats) was as nonplussed as I to hear about that plastic "thingy" that is supposed to align the clutch. Believe me, this board is read world-wide and not confined to the West Coast where such wonders are available at your local friendly auto accessory shop for just a few bucks. <!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Gilles[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->$3 ?... Too much<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:10 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->My tool is even cheaper!
1) Borrow your wife's broom
2) Saw off 12" from the top
3) With a sharp knife or blade reduce slightly the OD
at one end (until fits inside the clutch disc)
4) Install the pressure plate centering your "New"
handle within the pressure plate springs, tight nuts
5) Pull the handle from the engine (it works!)<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Mark Seelbinder[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Sorry, but that would be expensive at my house ;-) <nt><!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:46 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->No Thread<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony Natoli[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Gilles' Broom Handle...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 1:17 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->HA!... I did the same thing only was CAUGHT by my wife...
I was surprised to find a plastic molded one at Pep Boys for $5.99... if ya feel like splurging!
Let me know if ya want/need it or can't get one locally.
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]scot[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->if all else fails<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 7:20 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Depress the clutch,(or push on the throwout lever) just slightly and a cluch that isn't quite aligned will oftenshift enough to allow assembly<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->And if ya got the "chutzpa"!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 6 2001, 9:28 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I useta watch my old man use a remote starter switch and spin the engine while shouldering and forcing the trans forward.
Thank God we can't do that on an X!
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Mike Waggoner[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->My method...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 7 2001, 12:26 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Last time I did a clutch without the tool, I just left the stuff a bit loose so the clutch plate would still slide around if forced a little, and then wiggled the transmission into place. I then slid the tranny out VERY carefully, tightened the bolts, and reassembled.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]lezesig[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 60px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->* * W I N N E R * * W I N N E R * * W I N N E R * *<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 7 2001, 3:25 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 60px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Mike,
ROTGLMAO T H A T has to win some kind of award for your method !! Using the entire tranny as an alignment tool. I figure you must have come up with a real slick method for dollying the tranny around, right ? I chose the eggcrate and 2 x 4 shimming approach ( and still had to fight it ). lezesig '79 X 1/9<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony...[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 75px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Best Trans dolly yet!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 8 2001, 11:00 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 75px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I tried the 2x4 method once also... but opted for using a ROPE sling from above... which I operate... and a 24 year old kid below for the dirty work.
Works well, and ya don't even git dirty!
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001 at 4:36 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tony Carroll [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->This post may be of assistance to you brave souls contemplating replacing your clutch unit and throwout bearing (the latter highly recommended).
This assumes that you are withdrawing your transmission unit only and leaving the engine in situ. With the whole oily mess on the floor, it may be wise to inspect the flywheel face and have it skimmed if necessary. A very light smear of grease on the G/B input splines is an idea after cleaning up with a rotary wire brush to reduce the chances of the clutch plate freezing on the splines as I suspect happened to Michael Hartel. Young players may notice that the short G/B input shaft is fully floating and is not supported by a spigot bearing in the crankshaft. Further bad news is that the hole in the end of the crank is larger than the I/D of the clutch plate hub, ruling out the use of a mandrel to centre the plate on reassembly. The manual says to line up the clutch plate by eye. Well, really!
My answer was to turn up a dummy spigot from mild steel and drilled smaller than the clutch hub I/D and long enough to reach the crankshaft flange. This is then pressed into the crank. Turn up a suitable mandrel to fit both dummy spigot and clutch plate hub and hang the clutch plate on this while you tighten the pressure plate. The whole plot should then go back together as easily as it came out. By the way, this all refers to a Euro-spec '82 X but the US specs in this area appear to be the same in the manual.
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->An easyer way<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001, 9:15 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I use a large felt marker to cenetre the clutch.
I have ued this method meany times.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Good lateral thinking<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 3 2001, 10:41 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Nice one Warren. If I didn't have a lathe I may have thought of the same method but being brought up on North-South engines and "proper" gearboxes...<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Several forms of alignment tool.<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 1:20 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Warren,
How about this variation ? A Store bought Splined alignment tool. Yep, actually broke down and bought one for the first time. Sure worked sweet. Like buying a one time use tool. Often overlooked when firing the order for the bearing, plate, and disk....but a very small expenditure comparitively speaking. This one was made of a durable plastic also.
.
You have to admit....spinning one on a lathe does have more class !! The question to Tony is - did he choose a fine or course knurl on the handle end ?
.
Out for now,
lezesig '79 X 1/9<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Confused?$<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 7:12 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Why not order the correct alignment tool when you order the clutch parts? It is about $3!<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->alignment tool<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 4:05 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->That's the one we use, just an el cheapo plastic phony input shaft on a plastic ring. It says 'Fiat 128' on it. Use it to line up the disc while you bolt the pressure plate in place, and then hooah - up goes the tranny and the wiggling begins -Mac.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You forgot to tell them that the tranny goes on after the swearing . <NT>
<!-- google_ad_section_end -->[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 4 2001, 8:39 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 60px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->D'oh! I always forget the most critical step<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 6:22 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 60px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->And speaking of forgotten steps, please don't forget to take the alignment tool back OUT after tightening the pp bolts and before hefting that tranny up over your head or you will end up swearing
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 75px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I did consider mentioning that step...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:26 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 75px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->but I would be the last person to insult the intelligence of those who read and learn from this board. In passing and referring to my original post, where I come from, most Fiats were privately imported (especially X1/9's) and my local Continental car dealer (Ferraris, Alfas, Fiats) was as nonplussed as I to hear about that plastic "thingy" that is supposed to align the clutch. Believe me, this board is read world-wide and not confined to the West Coast where such wonders are available at your local friendly auto accessory shop for just a few bucks. <!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->$3 ?... Too much<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:10 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->My tool is even cheaper!
1) Borrow your wife's broom
2) Saw off 12" from the top
3) With a sharp knife or blade reduce slightly the OD
at one end (until fits inside the clutch disc)
4) Install the pressure plate centering your "New"
handle within the pressure plate springs, tight nuts
5) Pull the handle from the engine (it works!)<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Sorry, but that would be expensive at my house ;-) <nt><!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 12:46 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->No Thread<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Gilles' Broom Handle...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 1:17 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->HA!... I did the same thing only was CAUGHT by my wife...
I was surprised to find a plastic molded one at Pep Boys for $5.99... if ya feel like splurging!
Let me know if ya want/need it or can't get one locally.
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->if all else fails<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 5 2001, 7:20 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Depress the clutch,(or push on the throwout lever) just slightly and a cluch that isn't quite aligned will oftenshift enough to allow assembly<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->And if ya got the "chutzpa"!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 6 2001, 9:28 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I useta watch my old man use a remote starter switch and spin the engine while shouldering and forcing the trans forward.
Thank God we can't do that on an X!
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->My method...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 7 2001, 12:26 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Last time I did a clutch without the tool, I just left the stuff a bit loose so the clutch plate would still slide around if forced a little, and then wiggled the transmission into place. I then slid the tranny out VERY carefully, tightened the bolts, and reassembled.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 60px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->* * W I N N E R * * W I N N E R * * W I N N E R * *<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 7 2001, 3:25 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 60px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Mike,
ROTGLMAO T H A T has to win some kind of award for your method !! Using the entire tranny as an alignment tool. I figure you must have come up with a real slick method for dollying the tranny around, right ? I chose the eggcrate and 2 x 4 shimming approach ( and still had to fight it ). lezesig '79 X 1/9<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 75px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Best Trans dolly yet!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 8 2001, 11:00 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 75px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I tried the 2x4 method once also... but opted for using a ROPE sling from above... which I operate... and a 24 year old kid below for the dirty work.
Works well, and ya don't even git dirty!
Tony<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]