<TABLE cellSpacing=1 cellPadding=6 width="100%" border=0><TBODY><TR><TD colSpan=2><TABLE width="100%" border=0><TBODY><TR><TD style="PADDING-TOP: 4px" vAlign=top colSpan=2>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]D.I.Y. adjustable cam pulley<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 15 2001 at 11:05 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]scot [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Get a spare cam pulley,and in a drill press, carefully drill out the locating pin hole in the pulley to 5/16". Get about 6" of 5/16" cold rolled steel rod and in the drill press make several eccentric bushings, eccentric by differing amounts from 2 to 15 thousandths. (This is much easier with a lathe)Bushings should be just a little longer than the thickness of the pulley hub.(where you drilled thru) the bushing center hole is a close fit on the locating pin(.020)Replace the stock pulley with the modified one, fit a bushing so as to advance or retard the cam and try it out. take notes and experiment. Remember, a few thou close to the hub will make a couple degree change at the rim.Check ignition timing, idler tension and pulley bolt carefully with every change. This is for information only, I will accept no responsibility.(Usual Waiver) <!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Author[/FONT]</TD><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Reply[/FONT]</TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "n";n54_em = n54_em + "a";n54_em = n54_em + "t";n54_em = n54_em + "o";n54_em = n54_em + "l";n54_em = n54_em + "i";n54_em = n54_em + "a";n54_em = n54_em + "l";n54_em = n54_em + "@";n54_em = n54_em + "p";n54_em = n54_em + "a";n54_em = n54_em + "c";n54_em = n54_em + "b";n54_em = n54_em + "e";n54_em = n54_em + "l";n54_em = n54_em + "l";n54_em = n54_em + ".";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + "t"; document.write("Tony Natoli"); // --> </SCRIPT>Tony Natoli <NOSCRIPT> Tony Natoli </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->THANKS A LOT... Scot!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 1:06 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->So ya keep tweaking the cam gear until the intake valves start hitting the pistons and back off a bit???
You got more CAJONES than I do!
HA!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "r";n54_em = n54_em + "v";n54_em = n54_em + "i";n54_em = n54_em + "c";n54_em = n54_em + "e";n54_em = n54_em + "@";n54_em = n54_em + "i";n54_em = n54_em + "m";n54_em = n54_em + "p";n54_em = n54_em + "o";n54_em = n54_em + "r";n54_em = n54_em + "t";n54_em = n54_em + "a";n54_em = n54_em + "u";n54_em = n54_em + "t";n54_em = n54_em + "o";n54_em = n54_em + "t";n54_em = n54_em + "e";n54_em = n54_em + "c";n54_em = n54_em + "h";n54_em = n54_em + ".";n54_em = n54_em + "c";n54_em = n54_em + "o";n54_em = n54_em + "m"; document.write("steve ambrose"); // --> </SCRIPT>steve ambrose <NOSCRIPT> steve ambrose </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->1500's are safe to play with...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 7:43 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi Tony, not to worry, 1500's with stock cams,heads, and pistons are safe from valve damage no matter where the cam is timed. Even safe from broken t-belts.
1300's are safe up to a full tooth of timing change.
Steve<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "n";n54_em = n54_em + "a";n54_em = n54_em + "t";n54_em = n54_em + "o";n54_em = n54_em + "l";n54_em = n54_em + "i";n54_em = n54_em + "a";n54_em = n54_em + "l";n54_em = n54_em + "@";n54_em = n54_em + "p";n54_em = n54_em + "a";n54_em = n54_em + "c";n54_em = n54_em + "b";n54_em = n54_em + "e";n54_em = n54_em + "l";n54_em = n54_em + "l";n54_em = n54_em + ".";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + "t"; document.write("Tony Natoli"); // --> </SCRIPT>Tony Natoli <NOSCRIPT> Tony Natoli </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I coulda sworn it was the other way around...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 11:14 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I haven't been blessed with a failure... but I thought it was the 1300s that were safe and the 1500s that failed!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]scot[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You got it exactly right Tony!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:47 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Actualy it runs like **** long before you get very far from stock.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "n";n54_em = n54_em + "a";n54_em = n54_em + "t";n54_em = n54_em + "o";n54_em = n54_em + "l";n54_em = n54_em + "i";n54_em = n54_em + "a";n54_em = n54_em + "l";n54_em = n54_em + "@";n54_em = n54_em + "p";n54_em = n54_em + "a";n54_em = n54_em + "c";n54_em = n54_em + "b";n54_em = n54_em + "e";n54_em = n54_em + "l";n54_em = n54_em + "l";n54_em = n54_em + ".";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + "t"; document.write("Tony Natoli"); // --> </SCRIPT>Tony Natoli <NOSCRIPT> Tony Natoli </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Scot... reread your message...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 11:17 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Is **** GOOD or BAD??? Even if I substitute the "S" word... I still don't know if its good or bad... even if the "S" word is equal to **** or STINK!
HA!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]lezesig[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Very Good !<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:16 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Scott,
Spill the beans ? : ) Trial and error got you the range of selection for coencentrics didn't it ?
Holding to a thou or two on an X-Y vice is beyond difficult at best with a drillpress.
Hey....without a fourjaw on a lathe it should do, right !
Thanks for sharing the app
out for now,
lezesig '79 X 1/9
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]scot[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Lezisig, yes I tried to dill a little off center about a dozen times and got a range of ecentricity.<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:51 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->is a prerequisite for FIAT ownership<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "e";n54_em = n54_em + "r";n54_em = n54_em + "w";n54_em = n54_em + "i";n54_em = n54_em + "n";n54_em = n54_em + "@";n54_em = n54_em + "a";n54_em = n54_em + "r";n54_em = n54_em + "t";n54_em = n54_em + "b";n54_em = n54_em + "a";n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "m";n54_em = n54_em + "e";n54_em = n54_em + "n";n54_em = n54_em + "t";n54_em = n54_em + ".";n54_em = n54_em + "c";n54_em = n54_em + "o";n54_em = n54_em + "m"; document.write("Erwin Timmers"); // --> </SCRIPT>Erwin Timmers <NOSCRIPT> Erwin Timmers </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Apple Motors sells these pre-made<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 17 2001, 9:21 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I have no experience with them, but it seems a good idea. You can keep track of the changes more easily than with the Kent Cams wheel. And the sales person assured me you could leave the belt on to make the changes.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 15 2001 at 11:05 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]scot [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Get a spare cam pulley,and in a drill press, carefully drill out the locating pin hole in the pulley to 5/16". Get about 6" of 5/16" cold rolled steel rod and in the drill press make several eccentric bushings, eccentric by differing amounts from 2 to 15 thousandths. (This is much easier with a lathe)Bushings should be just a little longer than the thickness of the pulley hub.(where you drilled thru) the bushing center hole is a close fit on the locating pin(.020)Replace the stock pulley with the modified one, fit a bushing so as to advance or retard the cam and try it out. take notes and experiment. Remember, a few thou close to the hub will make a couple degree change at the rim.Check ignition timing, idler tension and pulley bolt carefully with every change. This is for information only, I will accept no responsibility.(Usual Waiver) <!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->THANKS A LOT... Scot!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 1:06 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->So ya keep tweaking the cam gear until the intake valves start hitting the pistons and back off a bit???
You got more CAJONES than I do!
HA!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->1500's are safe to play with...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 7:43 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi Tony, not to worry, 1500's with stock cams,heads, and pistons are safe from valve damage no matter where the cam is timed. Even safe from broken t-belts.
1300's are safe up to a full tooth of timing change.
Steve<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I coulda sworn it was the other way around...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 11:14 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I haven't been blessed with a failure... but I thought it was the 1300s that were safe and the 1500s that failed!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You got it exactly right Tony!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:47 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Actualy it runs like **** long before you get very far from stock.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Scot... reread your message...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 11:17 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Is **** GOOD or BAD??? Even if I substitute the "S" word... I still don't know if its good or bad... even if the "S" word is equal to **** or STINK!
HA!
Best Regards,
Tony Natoli
Two '79s, WHITE FANG and BLACK TOOTH
Santa Clarita, CA<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Very Good !<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:16 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Scott,
Spill the beans ? : ) Trial and error got you the range of selection for coencentrics didn't it ?
Holding to a thou or two on an X-Y vice is beyond difficult at best with a drillpress.
Hey....without a fourjaw on a lathe it should do, right !
Thanks for sharing the app
out for now,
lezesig '79 X 1/9
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Lezisig, yes I tried to dill a little off center about a dozen times and got a range of ecentricity.<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 16 2001, 10:51 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->is a prerequisite for FIAT ownership<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Apple Motors sells these pre-made<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 17 2001, 9:21 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I have no experience with them, but it seems a good idea. You can keep track of the changes more easily than with the Kent Cams wheel. And the sales person assured me you could leave the belt on to make the changes.<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]