<TABLE cellSpacing=1 cellPadding=6 width="100%" border=0><TBODY><TR><TD colSpan=2><TABLE width="100%" border=0><TBODY><TR><TD style="PADDING-TOP: 4px" vAlign=top colSpan=2>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Power loss when cornering, calling Ulix<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 29 2000 at 6:07 AM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tim [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I recently posted this question on the UKX club forum, and Julian (Tech advisor) says Ulix had this problem, when I take corners at high speed I get a sudden loss of engine power, which in less than a second comes back and carries on as normal, just like switching the ignition off and back on (only without the backfire), it ONLY happens going round bends fast otherwise the engine runs 100% ok, aparantly I need to construct a snorcle for the air corrector jets as they get flooded during high lateral g's ?, can you shed any light on this Ulix/anyone?<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Author[/FONT]</TD><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Reply[/FONT]</TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Ulix[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Which carb do you have?<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 29 2000, 8:55 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi Tim,
I had this problem with the stock carb (well, a 34DMTR actually) when autocrossing, but only in left turns I believe. The soulution was to lower the float level by 2 mm. This makes you car run a little leaner in general and you may have to change your jetting.
At last weekend's autocross, I discovered a similar problem, but in both left and right turns with my DCNFs.
Supposedly, fuel sloshes out of the float bowl vents and goes down the air correctors, flooding the engine. I could lower the float levels, but I think I rather try the snorkels, since the carbs are set up well otherwise.
All this involves is to find some tubing that has the right inner diamter to stick on the air correctors. A guy I talked to said he used plastic tubing that was a little too small and reamed it out slightly until it fits.
I will do this in the next couple of days and report back.
Ulix "no, I won't get fuel injection" Goettsch<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "j";n54_em = n54_em + "i";n54_em = n54_em + "m";n54_em = n54_em + "b";n54_em = n54_em + "r";n54_em = n54_em + "o";n54_em = n54_em + "1";n54_em = n54_em + "0";n54_em = n54_em + "0";n54_em = n54_em + "0";n54_em = n54_em + "@";n54_em = n54_em + "l";n54_em = n54_em + "a";n54_em = n54_em + "i";n54_em = n54_em + "r";n54_em = n54_em + ".";n54_em = n54_em + "f";n54_em = n54_em + "r";n54_em = n54_em + "e";n54_em = n54_em + "e";n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "r";n54_em = n54_em + "v";n54_em = n54_em + "e";n54_em = n54_em + ".";n54_em = n54_em + "c";n54_em = n54_em + "o";n54_em = n54_em + ".";n54_em = n54_em + "u";n54_em = n54_em + "k"; document.write("Julian"); // --> </SCRIPT>Julian <NOSCRIPT></NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Minor correction<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 1:47 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Maybe I'm just being pedantic Tim, but I'm not a technical advisor anymore.....I know I'm still offering advice to all and sundry on the forum, but I had to hand in my TA stripes when I took on the role of club secretary!
Julian<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tim[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Come now Julian...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 8:49 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You will always be known as 'THE' tech advisor, people will worship you as the god of all Exxy's and all things broken, missing or otherwise not as they should be.
.
.
.
.
That should earn a few browny points,No pun intended, snigger snigger ;-)_
It's a 34 DMTR 87/250, getting back to the problem in hand, do you mean fitting a pipe to the air corrector feed holes visible from the top of the carb,the bit that sits on top of the emulsifyer, I would have thought the gasket would stop any fuel getting up this high?<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Ulix[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Wrong carb!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 9:48 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Tim,
if it is a DMTR, the solution is to lower the float level. I lowered mine 2mm from the setting specified in the manual and this fixed my problem.
The snokel idea was for dual carbs (DCNF).
Ulix<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 29 2000 at 6:07 AM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Tim [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->I recently posted this question on the UKX club forum, and Julian (Tech advisor) says Ulix had this problem, when I take corners at high speed I get a sudden loss of engine power, which in less than a second comes back and carries on as normal, just like switching the ignition off and back on (only without the backfire), it ONLY happens going round bends fast otherwise the engine runs 100% ok, aparantly I need to construct a snorcle for the air corrector jets as they get flooded during high lateral g's ?, can you shed any light on this Ulix/anyone?<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Which carb do you have?<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]February 29 2000, 8:55 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi Tim,
I had this problem with the stock carb (well, a 34DMTR actually) when autocrossing, but only in left turns I believe. The soulution was to lower the float level by 2 mm. This makes you car run a little leaner in general and you may have to change your jetting.
At last weekend's autocross, I discovered a similar problem, but in both left and right turns with my DCNFs.
Supposedly, fuel sloshes out of the float bowl vents and goes down the air correctors, flooding the engine. I could lower the float levels, but I think I rather try the snorkels, since the carbs are set up well otherwise.
All this involves is to find some tubing that has the right inner diamter to stick on the air correctors. A guy I talked to said he used plastic tubing that was a little too small and reamed it out slightly until it fits.
I will do this in the next couple of days and report back.
Ulix "no, I won't get fuel injection" Goettsch<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Minor correction<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 1:47 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Maybe I'm just being pedantic Tim, but I'm not a technical advisor anymore.....I know I'm still offering advice to all and sundry on the forum, but I had to hand in my TA stripes when I took on the role of club secretary!
Julian<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Come now Julian...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 8:49 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->You will always be known as 'THE' tech advisor, people will worship you as the god of all Exxy's and all things broken, missing or otherwise not as they should be.
.
.
.
.
That should earn a few browny points,No pun intended, snigger snigger ;-)_
It's a 34 DMTR 87/250, getting back to the problem in hand, do you mean fitting a pipe to the air corrector feed holes visible from the top of the carb,the bit that sits on top of the emulsifyer, I would have thought the gasket would stop any fuel getting up this high?<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 45px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Wrong carb!<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]March 1 2000, 9:48 AM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 45px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Tim,
if it is a DMTR, the solution is to lower the float level. I lowered mine 2mm from the setting specified in the manual and this fixed my problem.
The snokel idea was for dual carbs (DCNF).
Ulix<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]