<TABLE cellSpacing=1 cellPadding=6 width="100%" border=0><TBODY><TR><TD colSpan=2><TABLE width="100%" border=0><TBODY><TR><TD style="PADDING-TOP: 4px" vAlign=top colSpan=2>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Air leak into cooling system, any tips???<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 14 2000 at 11:14 AM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Gilles [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi there:
Yesterday I replaced the thermostat (I removed the complete housing not just the bottom with the three 10mm bolts), also replaced the fan switch and installed a stainless water reservoir (Looks cool!).
In the past, every time I bleed the system I do it several times just to be sure I get all the air out (every time I get less and less out from the bleeder untill I don't get any more). However, this time is different it seems that every time I got to the bleeder it gets a lot of air out from the system.
Somehow it seems that the car is sucking air back into the system.
The gasket I used on the thermostat housing was used but in good condition (I didn't have a replacement handy) and no water is leaking out either.
Could be possible to suck air (a lot) by using a used gasket? I was sure to tighten all the hoses and clamps that I removed
Any suggestions here?
Thank you in advance, Gilles
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Author[/FONT]</TD><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Reply[/FONT]</TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "d";n54_em = n54_em + "c";n54_em = n54_em + "m";n54_em = n54_em + "e";n54_em = n54_em + "h";n54_em = n54_em + "l";n54_em = n54_em + "@";n54_em = n54_em + "y";n54_em = n54_em + "a";n54_em = n54_em + "h";n54_em = n54_em + "o";n54_em = n54_em + "o";n54_em = n54_em + ".";n54_em = n54_em + "c";n54_em = n54_em + "o";n54_em = n54_em + "m"; document.write("Danny"); // --> </SCRIPT>Danny <NOSCRIPT></NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Could be seeping head gasket<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 16 2000, 12:24 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Gilles, does your temp guage read higher than normal? If a head gasket seeps slightly it can leak combustion air into the cooling system. Usually this will pressurize/heat the cooling system enough to make it leak somewhere. I don't think your problem would be a bad cooling system gasket, as this would let coolant out, not air in. My other guess would be that there is a trapped pocket of air in the cooling system somewhere that is not getting bled the first time. I'm not sure of this, as I have zero experience working on X's (but to hope to get some soon!). Good luck.
-Danny
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Gilles[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Seeping head gasket means head gasket replacement?<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 16 2000, 4:20 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Yes, my temp gauge reads higher than normal (A little).
But I was attributing this to the air entering the system.
I have to bleed the air out every time I use the car, and the amount of air is as much as when you start the bleeding procedure.
I hope I don't have to replace the head gasket!
Will a compression test determine something here?
Any suggestions will be greatly appreciated.
Thanks in advance, Gilles
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 14 2000 at 11:14 AM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Gilles [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi there:
Yesterday I replaced the thermostat (I removed the complete housing not just the bottom with the three 10mm bolts), also replaced the fan switch and installed a stainless water reservoir (Looks cool!).
In the past, every time I bleed the system I do it several times just to be sure I get all the air out (every time I get less and less out from the bleeder untill I don't get any more). However, this time is different it seems that every time I got to the bleeder it gets a lot of air out from the system.
Somehow it seems that the car is sucking air back into the system.
The gasket I used on the thermostat housing was used but in good condition (I didn't have a replacement handy) and no water is leaking out either.
Could be possible to suck air (a lot) by using a used gasket? I was sure to tighten all the hoses and clamps that I removed
Any suggestions here?
Thank you in advance, Gilles
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Could be seeping head gasket<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 16 2000, 12:24 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Gilles, does your temp guage read higher than normal? If a head gasket seeps slightly it can leak combustion air into the cooling system. Usually this will pressurize/heat the cooling system enough to make it leak somewhere. I don't think your problem would be a bad cooling system gasket, as this would let coolant out, not air in. My other guess would be that there is a trapped pocket of air in the cooling system somewhere that is not getting bled the first time. I'm not sure of this, as I have zero experience working on X's (but to hope to get some soon!). Good luck.
-Danny
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 30px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Seeping head gasket means head gasket replacement?<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]August 16 2000, 4:20 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 30px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Yes, my temp gauge reads higher than normal (A little).
But I was attributing this to the air entering the system.
I have to bleed the air out every time I use the car, and the amount of air is as much as when you start the bleeding procedure.
I hope I don't have to replace the head gasket!
Will a compression test determine something here?
Any suggestions will be greatly appreciated.
Thanks in advance, Gilles
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]