<TABLE cellSpacing=1 cellPadding=6 width="100%" border=0><TBODY><TR><TD colSpan=2><TABLE width="100%" border=0><TBODY><TR><TD style="PADDING-TOP: 4px" vAlign=top colSpan=2>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Updated Tranny problem - (Pictures!)<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 2 2001 at 12:23 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "m";n54_em = n54_em + "s";n54_em = n54_em + "c";n54_em = n54_em + "h";n54_em = n54_em + "a";n54_em = n54_em + "f";n54_em = n54_em + "e";n54_em = n54_em + "@";n54_em = n54_em + "m";n54_em = n54_em + "e";n54_em = n54_em + "d";n54_em = n54_em + "i";n54_em = n54_em + "a";n54_em = n54_em + "o";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + ".";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + "t"; document.write("Matt Schafer"); // --> </SCRIPT>Matt Schafer <NOSCRIPT> Matt Schafer </NOSCRIPT> [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Well, I found the source of the leakage - here is the picture:
The arrow points to the part it leaks from. Its the little diamond shaped bracket thingy. I tried tightening it, but I snapped the bolt right in half!! So now there is only 3 instead of 4 bolts. Any suggestions to replace / fix this?
Thanks,
Matt
-------------------
'74 X1/9
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR><TR><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Author[/FONT]</TD><TD>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]Reply[/FONT]</TD></TR><TR><TD vAlign=top noWrap width="17.9%">[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "s";n54_em = n54_em + "e";n54_em = n54_em + "r";n54_em = n54_em + "v";n54_em = n54_em + "i";n54_em = n54_em + "c";n54_em = n54_em + "e";n54_em = n54_em + "@";n54_em = n54_em + "i";n54_em = n54_em + "m";n54_em = n54_em + "p";n54_em = n54_em + "o";n54_em = n54_em + "r";n54_em = n54_em + "t";n54_em = n54_em + "a";n54_em = n54_em + "u";n54_em = n54_em + "t";n54_em = n54_em + "o";n54_em = n54_em + "t";n54_em = n54_em + "e";n54_em = n54_em + "c";n54_em = n54_em + "h";n54_em = n54_em + ".";n54_em = n54_em + "c";n54_em = n54_em + "o";n54_em = n54_em + "m"; document.write("steve ambrose"); // --> </SCRIPT>steve ambrose <NOSCRIPT> steve ambrose </NOSCRIPT>[/FONT]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Pretty easy to fix...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 2 2001, 1:07 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi there.. you will want to replace the rubber axle boot(with seal) and that steel part (it's the differential carrier bearing retainer)has a rubber o-ring around it. The o-ring comes in a 4-speed trans gasket set. The boot can be ordered from any of the usual suppliers. You just have to remove the axle on the drivers side. Too bad about the broken bolt, you will have to deal with that at the same time. Good luck,
Steve<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[/FONT]</TD></TR></TBODY></TABLE></TD></TR></TBODY></TABLE>
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 2 2001 at 12:23 PM[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<SCRIPT language=Javascript> <!-- var n54_em; n54_em = ""; n54_em = n54_em + "m";n54_em = n54_em + "s";n54_em = n54_em + "c";n54_em = n54_em + "h";n54_em = n54_em + "a";n54_em = n54_em + "f";n54_em = n54_em + "e";n54_em = n54_em + "@";n54_em = n54_em + "m";n54_em = n54_em + "e";n54_em = n54_em + "d";n54_em = n54_em + "i";n54_em = n54_em + "a";n54_em = n54_em + "o";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + ".";n54_em = n54_em + "n";n54_em = n54_em + "e";n54_em = n54_em + "t"; document.write("Matt Schafer"); // --> </SCRIPT>Matt Schafer <NOSCRIPT> Matt Schafer </NOSCRIPT> [/FONT]</TD></TR><TR><TD vAlign=bottom colSpan=3><HR></TD></TR><TR><TD colSpan=3>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Well, I found the source of the leakage - here is the picture:
The arrow points to the part it leaks from. Its the little diamond shaped bracket thingy. I tried tightening it, but I snapped the bolt right in half!! So now there is only 3 instead of 4 bolts. Any suggestions to replace / fix this?
Thanks,
Matt
-------------------
'74 X1/9
<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top noWrap align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]
[FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD style="PADDING-LEFT: 15px" vAlign=top><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Pretty easy to fix...<!-- google_ad_section_end -->
[/FONT][FONT=Trebuchet MS, Verdana, Tahoma, Arial][/FONT]</TD><TD vAlign=top align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]July 2 2001, 1:07 PM [/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=1 width="100%" border=0><TBODY><TR><TD style="PADDING-LEFT: 15px">
[FONT=Trebuchet MS, Verdana, Tahoma, Arial]<!-- google_ad_section_start -->Hi there.. you will want to replace the rubber axle boot(with seal) and that steel part (it's the differential carrier bearing retainer)has a rubber o-ring around it. The o-ring comes in a 4-speed trans gasket set. The boot can be ordered from any of the usual suppliers. You just have to remove the axle on the drivers side. Too bad about the broken bolt, you will have to deal with that at the same time. Good luck,
Steve<!-- google_ad_section_end -->
[/FONT]</TD></TR></TBODY></TABLE><TABLE cellSpacing=0 cellPadding=4 width="100%" border=0><TBODY><TR><TD vAlign=top align=left>[FONT=Trebuchet MS, Verdana, Tahoma, Arial] [/FONT]</TD><TD vAlign=top noWrap align=right>[FONT=Trebuchet MS, Verdana, Tahoma, Arial]